Fishing with Rod Discussion Forum
Fishing in British Columbia => General Discussion => Topic started by: Eagleye on July 11, 2009, 07:19:52 PM
-
Last time I took my boat out I was in a bit of a hurry and forgot to unscrew the vent on my gas can... By the time I realized it was sucked right in and it was full of gas too. This made the hose pop off my outboard before I figured out what was going on. I then opened the vent and all was fine for awhile but the next day my motor started cutting out on me similar to the time my kill switch goofed up but that has been replaced with a new one. I think the problem this time is the gas hose is some how messed up because everytime it cuts out the motor seems dry and I have to pump it lots and while pumping it feels like there might be air in the hose or else it isn't sucking up the gas properly. I discovered that by having someone pump the bulb while the motor was running it would work fine but when they stopped it would eventually cut out. I just had my motor in for a yearly maintenance a couple months ago and it was it didn't need any repairs. Any suggestions?
-
You may have a dried up cracked o-ring at the quick-connect.
Sometimes it pays to get a new hose as they do eventually breakdown.
Change the fuel filter.
-
I guess I should have bought that service manual already... Is the o-ring on the gas line or the engine? Where abouts is the fuel filter? Thanks
-
Depends on the size of your motor? but most are inline beside the carbs.......make....size....matters?
perhaps try a new fuel line ,from the tank to the motor....I had a fuel line collaps (the inner liner), Check the fuel tank for debris...
Rieber was that you below peg leg today? barfing.......
-
its the fuel pump on the motor.
it uses check valves and diaphrams, along with engine pulses.
you will see it when you follow the fuel line, common and cheep to buy.
-
Second on the fuel pump diaphragm. Could also have collapsed part of the fuel line creating a restriction.
-
Last time I took my boat out I was in a bit of a hurry and forgot to unscrew the vent on my gas can... By the time I realized it was sucked right in and it was full of gas too. This made the hose pop off my outboard before I figured out what was going on. I then opened the vent and all was fine for awhile but the next day my motor started cutting out on me similar to the time my kill switch goofed up but that has been replaced with a new one. I think the problem this time is the gas hose is some how messed up because everytime it cuts out the motor seems dry and I have to pump it lots and while pumping it feels like there might be air in the hose or else it isn't sucking up the gas properly. I discovered that by having someone pump the bulb while the motor was running it would work fine but when they stopped it would eventually cut out. I just had my motor in for a yearly maintenance a couple months ago and it was it didn't need any repairs. Any suggestions?
Did you make sure that the vent is actually venting after the initial mishap.Was it damaged?
-
Thanks for the info. I think the vent on the gas can is working because it relased all the built up pressure when I opened it. I forgot to mention my motor is a 2 stroke 25 HP yamaha 3cylinders oil injection.
-
These motors are actually super simple once you get into them. Heres to hoping it's an easy fix to get you back on the river.
As far as trouble shooting goes, being able to pump the ball and having the motor fire shows you that it is a fuel intake problem and not something more complicated (or expensive) like the carb or ignition system.
-
glad to hear that it won't be a costly repair. I think I will bring it to my old neighbour whom used to fix em for a living and ask him to help trouble shoot it for me... unless of course he is on his yearly and lenghty trip to the Dominican Republic. I tend to think it is just the fuel line though.
-
no need to trouble shoot, you already did!
I discovered that by having someone pump the bulb while the motor was running it would work fine but when they stopped it would eventually cut out.
new fuel lines, primer and tank, will cost more then the fuel pump.
-
Borrow someone else's fuel line. It could be the bulb pump on it.
-
I ran into the same problem a week ago , I have a 30 Yamaha 2 stroke . I had bought 2 Yamaha 3 gallon tanks from Galleon and the 1 tank I ran into allot of air in the line and had to keep pumping the ball to keep it going . I switched tanks and it pumped up solid and ran great after that , and still does . I think my problem was my connector on the tank .
-
Thanks sounds like a new fuel line will do the trick.
-
I had the same problem. I replaced the fuel line and was good to go.
-
good to know thanks
-
Thanks for all the suggestions. The problem was the fuel line was cracked inside the tank. It was a used tank, I fixed it now and the pressure in the bulb is better than ever and my engine runs perfectly.